JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser.
Popular Searches
Recent Searches
We have teamed up with Klarna to offer our customers different options of Finance, find out more of what Klarna can offer you.
Starting at £190.00
Starting at £204.00
Starting at £38.00
Delivery: Usually up to 7 working days. FREE standard delivery included* (see our delivery zones)
Delivery of heavy and bulky items such as paving, are delivered to kerbside on a large vehicle with tail-lift offloading. You MUST tell us at time of ordering if this vehicle is too large. We may occasionally be able to offer a smaller vehicle at extra cost on request.
The roads to your address must have a hard surface and be accessible by a large delivery vehicle. The route and your delivery location must be free from obstacles such as overhanging trees or cables.
Your delivery point must be flat, level and a hard surface such as concrete or tarmac. Grass, earth and gravel are NOT suitable surfaces. Delivery is made to kerbside only using a manual pump truck.
Inspect your goods upon delivery and record details of any obvious damages on the driver's documentation. In most cases, even if there are a few breakages, it is best to accept the delivery.
All paving pallets are heavy and sizeable. Once delivered, you will be responsible for moving the goods. Always ensure pallets are opened at the top, NOT the sides and remove the goods evenly from the centre of the pack to prevent tipping.
Although we do not use hi-ab (crane) or moffett (mini-forklift) deliveries as standard, we always attempt to upgrade larger orders to this type of vehicle when possible. Please contact us for further information.
Please contact us if you have any concerns regarding delivery. Refer to our contract terms for further details.
Delivery charges are already included in the price of the goods to all of the areas shown in the YELLOW zone on the map. In the BLUE and RED zones, a top-up delivery surcharge applies on certain products.
Postcodes: AL, B, BA, BB, BD, BH, BL, BN, BR, BS, CB, CH, CM, CO, CR, CT, CV, CW, DA, DE, DH, DL, DN, DY, E, EC, EN, FY, GL, GU, HA, HD, HG, HP, HR, HU, HX, IG, IP, KT, L, LA, LE, LN, LS, LU, M, ME, MK, NE, NP, NG, N, NN, NR, NW, OL, OX, PE, PO, PR, RG, RH, RM, S, SE, SG, SK, SL, SM, SN, SO, SP, SR, ST, SS, SW, TF, TN, TS, TW, UB, W, WA, WC, WD, WF, WN, WR, WS, WV, YO
Postcodes: CA, CF, DG, DT, EH, EX, G, KA, LD, LL, ML, PL, SA, SY, TA, TD, TQ. (Some exceptions apply)
Postcodes: AB, DD, FK, IV, KY, PA, PH, TR. (Some exceptions apply)
Please contact us for prices to other areas. We would be pleased to quote on overseas deliveries if required.
With most orders of paving, stone, composts, bark and rubber, delivery takes around 2-4 working days, based upon your order being placed before lunchtime on a working day.
Turf and sedum arrive the following day as the product is cut fresh on the morning of dispatch, so let us know when you need it and we will arrange to have the goods cut and delivered overnight to ensure they stay freshGarden buildings and structures range from around 7-30 working days.
All products on our website show an indicative delivery schedule, so it's best to refer to this for more product specific information.
Yes! We offer several different delivery options on most of our products to suit even the tightest of schedules!
Please find below the various options, their prices and the cut-off times for ordering:
Whilst we will make every effort to deliver in accordance with any booked delivery service and 99% of deliveries will arrive on time, we cannot guarantee a delivery schedule and any failure to deliver on a specified day or time will not be a breach of contract. Will will be unable to offer any compensation or cover any direct costs of delays by our third-party haulier. Do not arrange for your contractor or any equipment hire until your goods have arrived and been checked.
Unless you have already opted for a premium delivery on a specified day, we will make every effort to prebook all orders for large items with you once they reach your local delivery depot. You will only hear from the delivery company once your goods have travelled through the delivery network to arrive with the depot closest to you and this may take a couple of days following the day you placed your order.
Do not worry if you do not hear anything for a few days as the delivery day is usually only booked once the local depot to you commences scheduling.
Our trusted hauliers will usually deliver anytime between 8am and 6pm on your chosen delivery day. Some of our hauliers will provide tracking, however some of them do not, so unfortunately, we can never guarantee an exact time.
If you prefer, there is always the option to upgrade your delivery to an AM service, for an additional charge if this is more convenient for you.
Do I need to be in?
We do advise that you or a representative are on site upon arrival of delivery just in case the driver experiences any difficulties finding or accessing your property. This way the problem can quickly be resolved at the time instead of the driver potentially having to come back on a different day which will incur costly re-delivery charges.
In saying this, it is not mandatory that you are home for delivery and we can request your goods are left without signature if preferred. It is important to note however, that goods are left entirely at your own risk and we advise you to check your delivered items and report any problems to us as soon as possible, but within a maximum of 7 days. If the driver encounters any problems accessing your property or leaving the goods in a safe position whilst you are not at home, he/she may choose to abort the delivery and redelivery arrangements will be at your cost. In all cases, the driver will need to offload the goods from the vehicle quickly and soon after arriving at your property. Any delays preventing him/her from doing so will incur costs for waiting.
Will the driver require assistance?
More often than not, the driver will manage the delivery without a hitch. However in some circumstances, the driver will need assistance. For example:
As a general rule, all large goods produced by the same company/ brand will arrive as one delivery and goods from different companies will arrive separately. Small items such as sealants, paints and mortar products will always be sent out separately on a smaller courier service.
Don’t panic though, if there are parts of your order that are due to come separately, we will always aim to let you know.
Yes, it is best to open the plastic wrap and examine the goods prior to signing your acceptance of them arriving in a satisfactory condition. If you have damages, ensure this is recorded on the driver's docket / device and report to us immediately. If you are unable to check the goods whilst the driver waits, please sign as 'possible damage'.
Due to the nature of the goods and the distance they have travelled, you may encounter a couple of broken slabs. In the majority of cases, these may be used for the smaller cut pieces you will need for your project. It is usual practice to allow 10% extra over and above your calculated requirements for the project and this allows for offcuts. In the majority of cases, any broken slabs will be part of this 10% calculation. If you have a large quantity of breakages, please notify us within 7 days following delivery via email and with clear photographic evidence, ideally showing the goods damaged within their packaging. We will look to replace or refund you for the damages.
As standard, your goods will be delivered kerbside (on the road adjaent to the kerb). The driver at his discretion and with your permission, may attempt to move the goods closer to your property. In all cases, the ground must be level and firm such as tarmac or concrete.
For larger orders it may be possible for delivery to be made on a vehicle with crane or mini-forklift which will often enable offloading onto your property. We will discuss this with you if it is a feasible option.
No, smaller items such as jointing compound or sealer will come by a standard courier service van. Some items such as base aggregates (sharp sand, cement etc) will arrive on a vehicle with crane offload.
All paving products sold by Paving Superstore are tested and conform to UKCA standards and hold a Declaration of Performance Certificate. This sets us aside from many other websites and guarantees you are buying a quality product designed to last. Let us tell you a bit more:
Strict EU regulations were introduced in 2013 to ensure all paving sold in the UK meets the minimum standards set out under European standards EN1341 (flagstones), EN1342 (setts) and EN1343 (kerbs), however MOST companies selling paving online DO NOT adhere to these legal requirements as it is not heavily policed by Trading Standards. ALL paving products sold by Paving Superstore are manufactured by leading brands and DO meet these standards. All products are CE marked / UKCA / UKAS accredited. UKAS is the National Accreditation body for the United Kingdom appointed by the government to ensure products meet the high standards needed to attain certification. All products also hold a valid Declaration of Performance certificate which details the tests and results for each of the necessary criteria which guarantees you that the products we sell are fit for purpose.
Test Process
The water absorption test measures the amount of water a stone can hold when fully saturated. This is expressed as a percentage of the total weight. So, a result of 1% means that when fully saturated, 1% of a stone’s weight will be water. As a guide, paving such as porcelain is usually less than 0.5% porosity, granite is around 0.5%, sandstone and limestone are in the region of 1-3% and concrete, 6%
Why is this important?
This is an indicator to how quickly stains will soak in and how quickly a stone will look dirty. The lower the number, the better it will deal with staining. Obviously other factors such as colour and texture will also play a part in the likelihood of staining. High levels of water absorption are also associated with increased algae growth which is known to be a problem with poor quality stone as this is often more porous as a result of it being an inferior standard.
Frost resistance testing is called the Freeze/ Thaw test and is conducted by repeatedly freezing the paving to -40 Fahrenheit and then thawing it, before repeating the cycle again. During this process the paving will lose some of its flexibility and the key to good quality paving is that it does not lose a high level of resilience during the test cycle. Losses in Mpa should not exceed 5 Mpa
with very low temperatures. Paving which is overly porous will crack in frost and it is essential that paving is tested to the above standard to be sure it can cope in all weathers.
The ‘flexural strength’ test shows how much bending a paving unit can be put under before it breaks. This is an important test measurement for paving, but not really for setts or blocks as they are not large enough to bend. The test data is normally expressed in mega pascals (Mpa) with higher numbers being better. A typical measurement with sandstone is over 13 Mpa, concrete 5 Mpa and porcelain is often over 40 Mpa
The flexural strength is important as it ensures the paving is not overly brittle which would cause difficulties when handling and laying.
The ‘compressive strength’ test shows how much a stone can be squashed before it breaks. This is most important for setts and blocks as these are often used on driveways. It’s expressed in mega pascals (Mpa) with higher numbers being better.
The compressive strength rating is important when deciding on stone suitable for a driveway or commercial setting where excessive weight will be applied to the paving. Paving that does not pass the required standard will not support any excessive loading.
Slip resistance testing is a complex and varied area however the two main tests for domestic paving are either the pendulum test (PTV) or the ramp test (R rating). With the pendulum test, a pendulum is swung over the surface of the stone which will slow it down. The rougher the surface, the more it will slow the pendulum and the higher the value (PTV). It is tested both wet and dry. The lowest permitted value for external use when wet is 36.
The ramp test (R rating) is often used for porcelain paving and this is conducted using a ramp which is gradually raised. Oil is applied to the ramp and a test person walks onto the ramp wearing boots. The measurement is taken from the point at which they slip. R11 is the rating usually applied to porcelain paving and this is equivalent to the value of 34 to 51 in the PTV test data (pendulum test value).
Ensuring paving has good slip resistant qualities is important for outdoor usage, especially when used by children or elderly people. There is no point installing stone that does not meet the specified criteria for outdoor surfaces as it will be dangerous and not at all suited to purpose.
The following table shows the slip test data ratings for both test types and the recommended usage for paving conforming to each result.
Further to stringent test procedures, all paving sold through Paving Superstore is ethically sourced with all manufacturers belonging to the Ethical Trading Initiative or alternative schemes. This promises that:
Please ensure you only buy ethically sourced natural stone
Mon-Fri 9am-5pm
0800 002 9910
Many can be priced and ordered on our website. Here's how:
Other products can still be split down for you, but cannot be calculated online. For these, follow the on-screen prompts. In summary:
If you need any assistance, then please give us a call on 0800 002 9910 or contact us here
Pay simply by debit or credit card including Mastercard, Visa, Amex and ApplePay.
Select this option to receive a manual invoice for payment by card, BACS or cheque
Looking to order a large quantity of products? We typically say orders over 10 packs are classed as a bulk Order. If you would like a bulk quote, its simple and easy to do with our online Quote Request System. Simply follow the below steps and your quote will be compiled by one of dedicated team members.
Once we have received your quote we will be in touch to give you a price, this will come via email. If you are happy with the quote, let us know via email and we will approve the quote for you. Then you can log into your online account through our website and pay for your quote there and then. If you would also like to see the progress of your quote that can also be seen within your online account.
Looking for a price on a product which says POA. Its simple and easy to do with our online Quote Request System. Simply follow the below steps and your quote will be compiled by one of our dedicated team members.
The Rowlinson Marberry Cascade Planter is an attractive and contemporary garden planter designed to add height, colour and dynamism to your garden displays. With sleek rounded corners, and delivered pre-assembled with fitted liner.
The Cascade Planter has 3 tiers with an attractive curved front, it fits in right angled corners. Can be used as 3 seperate planters.
Small Planter Approx 10 Litres Capacity.
Medium Planter Approx 51 Litres Capacity.
Large Planter Approx 135 Litres Capacity.
The premium Rowlinson Marberry Range which are finished to the highest standards, giving you the confidence to start creating stunning floral displays straight away.
A family business that has been trading in timber since 1926. With over 85 years of manufacturing knowledge and experience, you can be confident that their products are constructed to the highest standard and from the finest materials available. Rowlinson products are manufactured to standards set out in our Quality Management System, accredited to ISO 9001: 2008, and distributed from Cheshire.
Rowlinson Garden Products takes its social and environmental responsibilities very seriously in terms of Carbon Foot Print and responsible forest management and, as such, are Forest Stewardship Council (FSC®) certified and fully comply with all current regulations on FSC sourcing.
Product safety is a key part of their quality management system. They ensure where necessary our products are tested and approved to the most recent BS EN standards.
Wood Description:
Wood is a good option for garden features and buildings due to its aesthetic appeal, durability, sustainability, versatility, and cost-effectiveness. By choosing the right type of wood for your needs and taking proper care of it, you can create beautiful and long-lasting garden structures that enhance the beauty and functionality of your outdoor space.
Wood is a good option in the garden for several reasons:
Aesthetic appeal: Wood is a natural and attractive material that adds warmth and character to garden features and structures.
Durability: Many types of wood are naturally resistant to rot, decay, and insect damage, making them a long-lasting option for outdoor use.
Sustainability: Wood is a renewable resource that can be sustainably harvested and grown, making it an environmentally friendly option for garden features and structures.
Versatility: Wood can be easily cut and shaped to create a wide range of garden features and structures, from simple garden beds to complex arbours and pergolas.
Cost-effective: Many types of wood are an affordable option for garden features and structures, making them accessible to homeowners on a variety of budgets.
There are several types of wood that are commonly used in garden features and buildings, each with its own unique properties and characteristics.
Dip Treated Softwood
Softwood is a popular choice for garden features and structures such as garden sheds, fencing, and decking, due to its affordability and ease of use. Dip treating the wood with a preservative helps to extend its lifespan and prevent it from deteriorating over time.
The process of dip treating softwood involves immersing the wood in a tank or container of wood preservative. The wood is left in the solution for a period of time, typically between 10-15 minutes, to allow the preservative to fully penetrate the wood. The wood is then removed from the solution and left to dry, allowing the preservative to fully soak in. This means the exterior will be covered, but the treatment will not have penetrated deep into the wood.
Dip treated softwood is an effective way to protect wood from decay and insect damage, but it is not as durable as other types of treated wood, such as pressure-treated wood. Dip treated softwood requires regular maintenance, such as reapplying a wood preservative every few years, to ensure that it remains protected and in good condition.
Pressure Treated/Tanalised Softwood
Pressure-treated or tanalised softwood is a type of wood that has been treated with a preservative to protect it against decay, rot, and insect damage. The treatment process involves placing the wood in a pressure chamber and applying a preservative under high pressure, forcing it deep into the wood fibres. This makes the wood more resistant to moisture and insects, increasing its lifespan and making it suitable for outdoor use.
Tanalising is a specific type of pressure treatment that involves using a copper-based preservative, which gives the wood a greenish tint. The copper in the preservative helps to protect the wood against decay and insect damage, making it a popular choice for outdoor structures such as garden sheds, decking, and fencing. The colour of this treatment can sometimes be confused with mould. It is also possible for some presure treated items to be availble in brown.
Pressure-treated or tanalised softwood is a more durable and long-lasting option than untreated wood or dip-treated wood, and requires less maintenance. However, it is important to note that pressure-treated wood can be more expensive than untreated wood or dip-treated wood.
You should allow this wood to dry before applying any stain or paint for approx 2 months or more.
Hardwood
One of the advantages of hardwood is its durability and strength. It is less likely to dent or scratch, and it can withstand wear and tear better than softwood. It is more resitant to insect damage and rot. Additionally, hardwood is often considered more aesthetically pleasing than softwood due to its unique grain patterns and natural colours.
However, hardwood can be more expensive than softwood, and it may be harder to work with due to its density. Hardwoods offer more water resistance, meaning they are less likely to rot, suiting them to outdoor furniture. Hardwood benefits from annual treatments with oil and can last many decades with proper care and maintenance which makes it a great investment.
Natural Wood Characteristics:
All natural timber products are unique and will vary in markings, colour and texture, often showing distinctive markings. Sizes are nominal and may vary. Many dimensions are rounded or approximate. The product images shown are as accurate as photographic processes allow and may appear differently in accordance with lighting conditions and screen calibration in addition to the natural variation occurring between individual items. All natural timber products are unique and will vary in markings, colour and texture, often showing distinctive markings. Images may not be a true representation of a particular product size or use and may vary in line with manufactuers' changes to specification.
Wood is a natural material used in a wide range of construction projects and is known for its sturdiness, elasticity, noise reduction qualities and overall aesthetic appeal as a result of its natural characteristics. It will also swell, shrink and crack, release resins, display marrow, gnarls and graining, show inconsistent smoothness and ruggedness, release salts and exhibit pinholes and fungi/ mould.
All of these characteristics are expected with wood and can be explained as follows. Swelling, shrinkage and cracking is caused by the humidity in the atmosphere altering the volume of the wood. Resins escape from the wood usually in the first year following manufacturing. They fall off naturally of may be planed. Marrow, gnarls and grains are unique, natural characteristics of the tree. Rugged areas are where the natural texture of the wood differs and despite milling, cannot be removed. Salts, mould and fungi are caused by the humidity in the atmosphere and are usually a temporary phenomenon. Similary, pressure treated wood often shows markings that may appear to be mould, but are in fact a build up of the treatment applied which may be removed by hand or will gradually weather away. Pinholes are produced by small xylophagous insects. These insects were killed while processing the stem into the end product. Wood, the same as any natural material will never be 'perfect' as the beauty of the material is the variation in colour, texture and finish.
Please ensure all natural wood items are treated with a good quality wood preserver soon after installation to protect the product against weathering.
You might want to take a look at more products we have in this range.
